The secretary general of the Organization of Petroleum Exporting Countries (OPEC) said recently that US economic sanctions against Venezuela have affected global energy supplies.
He told Venezuelan media that the ECONOMIC sanctions imposed by the United States on Venezuela and other countries have seriously affected the ability to produce and export oil worldwide and violated the right of people in other countries to use energy.
Venezuela has one of the largest proven crude oil reserves in the world, but U.S. sanctions have made it impossible for Venezuela’s oil industry to consistently export reliable energy to the world, he said. Despite this, he highly appreciated the efforts of the Venezuelan oil industry to maintain concrete foaming agent are expected to increase in the future.
The cement foaming agent is the key to the quality of foamed concrete. A good cement foaming agent can be made into high-quality foamed concrete. The following is a talk about how each performance index of cement foaming agent affects the quality of foamed concrete.
1. The more uniform the better, the bubble diameter should be the same size
The more narrow the ideal pore size distribution the better, that is, the pore size of the pore is as consistent as possible, the difference is not too big. The corresponding requirements of the foam should be uniform, not different sizes. The bubble diameter of the foam cannot be the same but should be similar, the bubble diameter range as small as possible, and the difference between the maximum and minimum bubble diameter is not too big. It is required that the pores formed by the foam be uniform, which can avoid the concentration of compressive stress in the bullae and reduce the compressive strength. If the size of the foam is not uniform, the stress is concentrated in the bullae, which is very easy to cause it to become a weak link and crack first when under pressure.
2. The higher the foam stability, the better; the longer the stable bubble time, the better
Foam with good stability has tough liquid film and good mechanical strength, which is not easy to burst or excessive deformation under slurry extrusion. In addition, it has self-retaining water, the water on the liquid film is not easy to be lost under the action of gravity and surface tension, and can keep the thickness and integrity of the foam liquid film for a long time so that the foam can stay for a long time without bursting.
The stability of foam has three influences on the porosity: it can make most of the foam not disappear, and it is fixed in the foam concrete after the initial setting of the slurry to form the porosity. If the foam stability is not good, most or a small part of the foam will burst after pouring, forming few pores, and even make the slurry collapse soon after pouring, which is commonly known as collapse mold, resulting in complete failure of pouring.
Foam with good stability, the slurry is not easy to be deformed too much under extrusion, and has certain pressure resistance to keep itself approximately spherical, which can eventually form spherical pores with good shape;
Foam with good stability, the liquid film is not easy to burst in the slurry body, and it is not easy to form connected holes formed by gas collusion after bursting. Therefore, it eventually forms an ideal closed hole. The less stable the foam, the fewer closed holes, and the more connected holes. Therefore, the stability of foam should not only not collapse after pouring as the standard, but should not collapse after pouring, the final formation of pores approximately spherical, disconnected three indicators as the standard. Most people take no collapse after pouring as the standard to measure foam stability, which is a misunderstanding in understanding and the lowest standard of foam stability.
When there is no standard measuring instrument to measure the foam stability, the foam stability time can be used to measure the foam stability. The foam stabilization time should meet the initial setting needs of the cementitious materials used. After the initial coagulation of the slurry, it can fix the foam, retain the shape of the foam, and make it into an st.
As we know, any cementing material, including cement and magnesite, has an initial setting time, especially the most widely used ordinary Portland cement, the initial setting is mostly later than 45min. If the foam stability is poor, cement and other cementing materials have not set, the foam has burst, then the foam cannot form pores in concrete. In general, the minimum requirement for foam stability is to make the foam stability time longer than the initial setting time of the gelled material of 10 ~ 20min. As the initial setting time of various cementitious materials is not consistent, the foam stability time is also different. In general, the foam stability time for fast gel setting materials can be shorter, while the foam stability time for slow gel setting materials should be as long as possible. Even if the same cementitious material, temperature ma is different, its initial setting time is different, the change is quite big. For example, put Si cement needs 40min to set in summer, and in the winter of 5℃ below, 80min will not set in the beginning. Therefore, the stabilization time of bubbles cannot have a constant specific standard, should be determined according to the situation. To make the foam adapt to the needs of various use conditions, it should be stabilized for as long as possible.
Generally speaking, the stabilization time of bubbles should meet the following requirements:
1. When used in Portland cement and without coagulant, the stability time should be greater than 60min; The ideal maximum is greater than 3h;
2. When used in sulphoaluminate cement, high alumina cement, ferric aluminate cement, fast setting Portland cement, and other fast setting cement, the stability time should be greater than 30min, preferably greater than 60min;
3. When used in magnesium cement, the foam stability time should be greater than 40min and preferably greater than 80min;
4. When used for cementitious materials mixed with a large amount of filler or active waste slag such as fly ash, the foam stability time should be extended. The larger the amount of filler or active waste residue is, the longer the foam stabilization time should be.
The specific bubble stability time should be determined by a small test, so as to not collapse after pouring, not connected after the formation of pores, and not excessive deformation as the principle. The big rule is that the longer the bubble, the better.
Suppliers of Concrete Additives
TRUNNANO is a reliable foaming agents supplier with over 12-year experience in nano-building energy conservation and nanotechnology development.
If you are looking for high-quality CLC foaming agents, please feel free to contact us and send an inquiry. (email@example.com)
We accept payment via Credit Card, T/T, West Union, and Paypal. TRUNNANO will ship the goods to customers overseas through FedEx, DHL, by air, or by sea.
The current international situation is highly uncertain, and its economic impact has not been able to be assessed properly. In addition, rising energy and commodity prices and supply chain disruptions are expected to push the price of the concrete foaming agent higher.
US President recently decided to invoke a Cold War-era defense law to encourage domestic In625 powder. The history of superalloys dates back to the 1950s and 1960s, when researchers combined molybdenum and niobium with nickel to produce s…
Under the premise of ensuring the quality of concrete, early strength agent can greatly shorten its final setting time, make it as early as possible, and then accelerate the turnover of template, save template dosage.…
OPEC+ is likely to stick to its plan for a small increase in oil powdered instant sodium silicate will continue to be influenced by the oil supply shortage. About Powdered Instant Sodium Silicate CAS 1344-09-8 Sodium Silicate Powder:Sodiu…